MaKa

I get it, we all want to make money from our hard work. The problem is when developers start forcing things on the end user. Piriform is a prime example of how to alienate a user base. I personally have no problem paying or donating for "Premium" features. I'm aware of your beef with Amazon but the users of your program have nothing to do with that. I have a monthly internet bill and have a limited ammount of usage each month therefore it irritates me when developers feel they have the right to use my bandwith to make a profit when they don't chip in on paying my bill each month. I'm sorry to say but i feel that this current model is going to push users in a different direction which is unfortunate.

Well, the new ads window has prompted me to seek an alternative to this program. If that was the intended goal then job well done.

No it doesn't. Perhaps because the addon is for x86 only?

When using WinRAR for an SFX there is no need to set the path for the temp folder.On the modes tab just check the box that says "Unpack to temporary folder". Also in the "Run after extraction box" there is no need to type in the path either. You would only need this, setup.exe /VERYSILENT. Not everyone will always be installing your SFX on the C: so it may cause issues for those people the way you have it set up. Also if setup.exe is an Inno Setup installer (just guessing based on your first post) try these switches. /VERYSILENT /SUPPRESSMSGBOXES /NORESTART /SP-

That's pretty much the only way to test it.Quickest way is to Integrate only the addons and nothing else.Install Windows in Virtual Box or a similar program and check out the addon.

Much appreciated.Thank you.

Getting a "404 File Not Found" error when trying to download the Sources folder.

Auslogics Disk Defrag is a vital maintenance tool that will improve your PC’s performance by defragmenting and re-arranging files on your disk. This software was designed to remedy system sluggishness and crashes caused by disk fragmentation. Auslogics Disk Defrag is extremely simple to use, does not require any analysis phase and is faster than most of the other disk defragmentation software. It will help you get the maximum performance out of your expensive hardware investments. Places system files to the faster part of the disk, minimizing the time needed for the hard drive to access them. Merges scattered pieces of free space into a contiguous block, preventing fragmentation of newly created files. Shows you the list of all fragmented files and their clusters location on the disk after performing disk analysis. Minimizes growth of the VSS storage area and reduces the chance of overwriting previous VSS snapshots. Can be set to start defragmentation automatically when computer has been idle for 15 minutes. Auslogics Disk Defrag® is designed for fast optimization of today’s modern hard disks. Get the maximum performance out of your expensive hardware investments. Can save your time by defragmenting only necessary files, instead of defragmenting an entire hard drive. It works on Windows 7/2008/Vista/2003/XP (32-bit and 64-bit). Auslogics Disk Defrag is not just a defragmenter any more, but a fully featured disk optimizer. And with all the advanced techniques of disk optimization it has, Disk Defrag 3 remains extremely compact and even easier to use! Homepage http://www.auslogics.com/en/software/disk-defrag/ Addon: Architecture: x86 Language: en-US Uninstallable: No Size: 5.59MB Created: 8/31/2012 MD5: c64b357bcabe35d08051200efeaf5bd6 SHA1: d2af3a308fe1c3e9223c5d72b8bcc869df4c3fdd Download http://www.mediafire.com/?57o8sk6d25j2kg5 Silent Installer (No Switches Needed): Size: 4.89MB MD5: 0368fcba7f3b93be7b8c9144a1a3bb2d SHA1: f5bc3383e166fe4b4419789026cb31a4025c75c3 Download http://www.mediafire.com/?i86cc73jf4b1bd8

I spent a few hours trying to figure it out myself.It worked fine with older version but not the new version.If you want to use the new version and have Firefox show up in add/remove programs then here's how to do it.Download the official Firefox installer from Mozilla, add it to the SFX tab in the All-In-One Integrator, use the switch -ms and it will show up.It's an odd issue but hopefully the developer will get it worked out.

Architecture: x86 Language: en-US Uninstallable: Yes Size: 18.69MB Created: 8/30/2012 MD5: 7c10bb5a054a1948e29ed8c2b9c7406f SHA1: d5bd9b4efe78c0b4bbfc8af5d3daf4020d87d6e2 Download Link http://www.mediafire.com/?7b2cb7b1b91xjau

I'll give that a shot then.Thanks for the info.

@Simpuhl It took 16 hours for one Win 7 installation disk? I don't feel so bad now. Hardly seems worth the effort if it takes that long. P.S. Does anyone happen to know the silent switches that will allow .NET 4.5 to install? I tried /silent /norestart but after running my image through Virtual Box, It wasn't installed.

Thanks for the info.So i guess to be on the safe side i will do mine from scratch also.I have 82 updates,3 addons and some tweaks which run me about 45 minutes so i was hoping there would be a simple way just to integrate the new stuff.I also wasted about 30 minutes trying to add .NET 4.5, unsuccesfully i might add.

Surely someone must be able to answer this question.Does everyone here just build a new image when there are new updates to add?

I have recently used Win Toolkit to integrate all my windows updates into my Windows 7 install disk.Next month there will be more updates coming out and i was wondering how i go about adding those in.When loading my modified image into Win Toolkit it asks me if want to load my saved preset.I'm not sure if i need to load that preset or not just to update my image with a few more updates.If i do not load the preset and just integrate the new updates, will my image still contain my previous updates that i added and all my tweaks? Any help would be greatly appreciated.